fire retardant logo

Fire Retardants Texas - Fort Worth/Dallas based

Hotline: 800-333-9197 7am-5pm (CST) Ph: 817-740-9197

After Hours: 817-658-9197 / email: fireprod@aol.com

2653 Warfield Street Fort Worth, TX 76106

Dallas, Ft Worth, Austin, Houston, Corpus Christi, Wichita Falls, Abilene, Amarillo, Plano, North Dallas, El Paso, Laredo, Frisco, South Dallas, Lancaster, Dallas County, Tarrant County, Odessa, Waco, Midland, Tyler, Dallas, San Antonio,Lubbock, East Dallas, Grand Prairie, Irving, Dallas / Fort Worth metroplex
Home About Us
fire retardant logo
FIRE POLY 100

INTERIOR/EXTERIOR FIRE RETARDANT
COATING or SPRAY
FOR ALL WOOD PRODUCTS
PLYWOOD ● LUMBER ● TIMBER


  CLASSIFIED
19P5
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING

Surface Douglas fir

Flame spread 5
Smoke developed 125
Number of preliminary coats None
Rate per coat (ft2/gal) --
Number of fire retardant coats 3
Rate per coat (ft2/gal) 360
Number of overcoats None
Rate per coat (ft2/gal) --
Flash point of liquid coating:  
   Fire retarding coating - closed cup, no flash



FIRE POLY 100 TECHNICAL DATA

ASTM E-84 CLASS A    UL 723 TYPE 1


PRODUCT DESCRIPTION:    Aqueous Based Resin


Product
Analysis
Total Solids
51%
PH
1.9-2.2
Weight per gallon
11.1lbs
Flash point
Non-Flammable
Specific gravity
1.33
Color
Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability
Non-Volatile
Solvents
Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus
excellent Resistance
Bacterial
Good Resistance
Linear shrinkage
None
Moisture Absorption
None
Corrosive
Mildly
Toxic
None (when dry)
Insects, rodents,
aspergilli And other types of molds
Excellent resistance
Termites
Excellent resistance
Preservative for wood
Good
Scrubability
1000 cycles

RECOMMENDED USE: Interior/Exterior Class A Rating (Flame spread < 5)

FLAME SAFE FIRE POLY100 is a fire retardant coating. It can be used on any type of wood, porous, or non-porous materials, such as:

Yellow pine Redwood Cedar Douglas Fir
Maple Oak Poplar Walnut
Cyprus Mahogany Teak Thatching
Bamboo Koa Ponderosa Pine Plywood

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.


QUICK REFERENCE FOR APPLYING FIRE POLY 100

MATERIAL APPLICATION
COVERAGE
Exterior/Interior wood
any type of wood
Treat before, during or after construction.

Be sure surface is clean and dry before treating.

Apply with brush or roller.

May be necessary to wipe on hardwood surfaces

Treat all surface areas where possible

Do not expose treated area to moisture for 24 hours.
Apply two (2) coats at 360 sq. ft. per gallon with the final coverage rate of 180 sq. ft. per gallon

EXTERIOR / INTERIOR WOODS

            All surfaces to be treated must be clean and dry. Fire Poly 100 is water-based, clear liquid that becomes insoluble when dry. On exterior wood Fire Poly 100 can last five years or more, while maintaining a flame spread index of less than 20. In extreme weather conditions it may be necessary to re-coat surfaces every three to five years. It also acts as a preservative, waterproofing agent, ultra violet inhibitor, mold and mildew inhibitor, and it repels insects. If over coating is intended, Fire Poly 100 is an excellent surface primer for use under latex paints, or can be used as a finished coat over water based stains. Finished surfaces will exhibit semi-gloss to gloss finish similar to lacquers or epoxies.

DO NOT DILUTE OR MIX FIRE POLY 100 WITH ANY OTHER PRODUCTS.

            Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

            Fire Poly 100 when applied according to the manufacturer’s specifications is the most effective fire retardant coating available.

CAUTION:

          Product must not freeze. It must not be thinned or diluted.


OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.


CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

 

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.


          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).


SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.


HOME | CONTACT US | FIRE RETARDANT WOOD